磁性术语

Term Glossary

AL Value (nH/N2): The inductance rating of a core in nanohenries (10-9 henries) per turn squared based on a peak AC flux density of 10 gauss (1 millitesla) at a frequency of 10 kHz. Note: 35.0 nH/N2 = 350 μH for 100 turns = 35.0 mH for 1000 turns.

Butt-Gap: The gapping of E Cores by equally spacing all three legs of the cores rather than introducing a gap in the center-leg only. Twice as much center-leg gap is required to electrically duplicate a given butt-gap.

Choke: Another term for an inductor which is intended to filter or choke out signals. 

Common-Mode Noise: Electrical interference that is common to both lines in relation to earth ground. 

Copper Loss (watts): The power loss (I2R) or heat generated by current (I) flowing in a winding with resistance (R). 

Core Loss (watts): The power loss or heat generated by a magnetic material subjected to an alternating magnetic field. 

Cross-Sectional Area (A): The effective cross-sectional area (cm2) of a core available for magnetic flux. The cross sectional area listed for toroidal cores is based on bare core dimensions with a 5% radius correction. 

Differential-Mode Noise: Electrical interference that is not common to both lines but is present between both lines. This is also known as normal-mode noise. 

Energy Storage (1/2 LI2): The amount of energy stored in microjoules (10-6 joules) is the product of one-half the inductance (L) in microhenries (10-6 henries) times the current (I) squared in amperes. 

Full Winding: A winding for toroidal cores which will result in 45% of the core’s inside diameter remaining. A winding for E Cores which will result in a full bobbin. The type of insulation, tightness of winding, and coil winding equipment limitations will all introduce variations. 

Initial Permeability (μo): That value of permeability at a peak AC flux density of 10 gauss (1 millitesla). μ=B/H. The permeability listed for each material is for reference only. The cores are manufactured to the listed AL values.

Magnetizing Force (H): The magnetic field strength which produces magnetic flux. 1 oersted = 79.58 A/m = .7958 A/c

 

For any additional definitions, clarifications or technical support please use our contact form or send an email to applications@micrometals.com

Mean Magnetic Path Length (l ): The effective magnetic length of a core structure (cm).

MLT (cm): The mean length per turn of wire for a core.

Peak AC Flux Density (Bpk): The number of lines of flux per unit of cross-sectional area generated by an alternating magnetic field (from zero or a net DC). In general: (1 gauss = 10-4 tesla) 

Peak to Peak Flux Density (∆B): In an alternating magnetic field, it is assumed that the peak to peak flux density is twice the value of peak AC flux density. ∆B = 2 Bpk. 

Percent Initial Permeability (%μo): Represents the percent change in permeability from the initial value. Since the cores are manufactured to the AL value rather than to the listed reference permeability, this can also be considered Percent AL Value. 

Percent Ripple: The percentage of ripple or AC flux to total flux; or in an inductor, the percentage of alternating current to average current. 

Percent Saturation: This is equal to 100% – Percent Initial Permeability. ie: 20% saturation = 80% of initial permeability. 

Simple Winding: A winding for toroidal cores which will result in 78% of the core’s inside diameter remaining. Often times this will produce a single-layer winding. 

Single-Layer Winding: A winding for a toroidal core which will result in the full utilization of the inside circumference of the core without the overlapping of turns. The thickness of insulation and tightness of winding will affect results. 

Swing: A term used to describe how inductance responds to changes in current. Example: A 2:1 swing corresponds to an inductor which exhibits 2 times more inductance at very low current than it does at its maximum rated current. This would also correspond to the core operating at 50% of initial permeability (also 50% saturation) at maximum current. 

Surface Area (cm2): The effective surface area of a typical wound core available to dissipate heat.

Temperature Rise (∆T): The increase in surface temperature of a component in free-standing air due to the total power dissipation (both copper and core loss).


美克顿微金属电感设计和分析软件

Inductor_Tool

美克顿微金属电感设计软件是一个非常有价值的工具,可以根据您的重要指标帮助确定最适合您应用的磁心。美克顿微金属电感设计软件将自动计算出满足指定需求的最小铁芯尺寸,并将显示计算结果和建议考虑的铁芯,包括微金属零件号、铁芯AL值、所需匝数、铁芯损耗、铜耗和温升。还可以显示铜线的绕线尺寸和重量。该软件允许设计工程师根据用户指定的电气要求快速制定出多个设计解决方案。


该软件的一个重要功能是可以为设计以图形方式显示预测的磁心温度随时间和温度的变化。此功能将允许设计工程师查看设计是否能够满足最低预期寿命。该图表将显示100,000小时内预测的磁心温度变化。


在检查和排序可用的解决方案之后,可以将选定的设计移到我们的电感分析模块中,以进一步优化线径、绕组或其他规格。用户甚至可以并排比较几种不同的设计变化,以便于分析和优化。


免费的美克顿微金属电感设计和分析软件使得寻找精确的解决方案变得容易!

美克顿微金属电感设计和分析软件